Aluminium Doors, Custom Built for Australian Homes and Builds
Aluminium doors do the work that no timber or steel door does as well, with slim sightlines, wide spans, low maintenance, and corrosion resistance that holds up against Australian coastal exposure. We manufacture custom aluminium doors across the full configuration range, including sliding, hinged, aluminium bifold doors, and aluminium stacking doors, sized to your openings, finished to your specification, and delivered to sites across Sydney, NSW, and Melbourne projects on a six to eight week lead time.
Why Builders and Homeowners Choose Aluminium Doors
Aluminium doors carry the structural strength to span wider openings than any other material, which is why bifold aluminium doors and aluminium stacking doors are the default specification for indoor-outdoor connections on modern Australian builds. Six-panel bifolds running 5,400 mm wide, three-panel stackers framing alfresco openings, and four-panel sliding doors on patio retreats – none of these spans work in timber or uPVC at the same sightline and operational reliability.
The corrosion resistance matters as much as the spanning capacity. Coastal salt air, western sun, and Australian climate swings degrade timber and warp uPVC inside a decade. Powdercoated aluminium frames hold their finish, their seal, and their operating tolerance for 30 to 40 years before frame replacement is on the table. That service life, combined with the thermally broken framing options now available across the range, is why aluminium has become the standard for both residential renovations and commercial builds.
What We Supply in the Aluminium Door Range
The full custom door range is sized and finished to project specifications.
Aluminium Bifold Doors
Two to seven panel configurations, opening to either side of the frame or splitting the stack between left and right. Aluminium bifold doors run on top-hung tracks for smoother long-term operation and lighter sash weight on the sill, with integrated flyscreen options and weather seals tested to commercial wind and water ratings. Spans up to 5,400 mm in a single run, larger by combining adjacent door sets.
Aluminium Stacking Doors
Three-, four-, and six-panel aluminium stacking doors that slide and stack against a fixed jamb, clearing two-thirds to three-quarters of the opening for the widest practical view when fully open. Useful where the architecture wants a continuous glass wall in the closed position and a single large opening when entertaining. Pocket-door variants are available where the wall depth allows the stack to disappear entirely into a cavity.
Sliding and Hinged Aluminium Doors
Two and three panel sliding doors for patios, balconies, and standard alfresco openings where the budget or wall layout does not call for a stacker or bifold. Single and double hinged aluminium doors for side entries, courtyards, and secondary access with multi-point locking. marine-grade hinges, and matching frame profiles to the rest of the door range so the façade reads as one system.
Built for Australian Construction Standards
AS 2047 Certified
Independent test reports for structural strength, air infiltration, and water penetration on every aluminium door series. Documentation is packed with the order so your certifier signs off the door schedule on the first pass.
BASIX and NCC Compliant
U-values and SHGC ratings on every glazing option, with thermally broken framing and double-glazed IGUs available where the energy spec demands it. Compliant for NSW BASIX and Victorian energy assessments on Melbourne project work.
Custom Manufactured
No off-the-shelf sizes forced into non-standard openings. Every panel is sized to your opening dimensions, every threshold detailed for your floor finish, and every stack direction specified at ordering.
Sydney, NSW, and Aluminium Doors Melbourne Delivery
Sydney metro direct delivery and NSW regional freight are included on most quotes, and aluminium doors Melbourne project work is quoted with freight as a separate line on the same six- to eight-week lead time.
Frequently Asked Questions
Aluminium bifold doors clear the entire opening when fully folded back, which suits entertaining areas where you want the wall to disappear completely. Aluminium stacking doors clear roughly two-thirds to three-quarters of the opening, with the stacked panels sitting visible against the jamb. Stackers tend to read cleaner in the closed position because the panels are wider and the sightlines are continuous; bifolds open more completely but show stacked panels at the hinge end. Spans above 4,800 mm usually favour stackers for the smoother operation; narrower openings under 3,000 mm often favour bifolds for the full clear opening.
Aluminium doors typically run 30 to 40 years before frame replacement is on the conversation, with hardware servicing every 8 to 12 years on the bifold and stacker tracks and gasket replacement at the 20 to 25 year mark. Coastal sites within five kilometres of the ocean should specify marine-grade powdercoat, which carries a 15-year finish warranty and demonstrably holds up better against salt-driven finish degradation.
Individual bifold aluminium door panels run up to roughly 1,000 mm wide and 2,400 mm tall, with the total opening spanned by combining panels in 2-panel, 3-panel, 4-panel, 5-panel, 6-panel, and 7-panel sets. Maximum single-run span is approximately 5,400 mm; larger openings are achieved by mullioning adjacent bifold sets with a structural mullion. Panel direction at the hinge can be specified left, right, or split for the larger configurations.
Yes, where the wall depth allows. Cavity-pocket aluminium stacking doors slide the panels into a framed cavity inside the wall, leaving the opening completely clear and the door panels invisible when open. The cavity needs roughly 110 mm of wall depth per panel plus track allowance, which suits stud-frame construction better than masonry. We coordinate the cavity detail with your framer at the quote stage so the pocket lines up with the door manufacture.
Yes. Aluminium doors Melbourne project work is quoted job by job, with freight from the Caringbah factory as a separate line item. Lead time matches Sydney's supply at six to eight weeks from order, and BASIX-equivalent Victorian energy data is supplied with every glazed unit so the Melbourne assessor has what they need. Builders running portfolios across both NSW and Victoria can send a combined opening schedule, and we will price the Sydney and Melbourne legs together.
Get a Quote for Your Aluminium Door Project
Send your opening schedule, BASIX or NCC energy spec, and any architectural drawings. We will quote against the project, confirm the lead time in writing, and stay reachable from order through delivery – no shifting answers, no missed delivery dates.
